Free guide · Xerox Builders

Fall protection for BC residential builds · November 2026

Falls are one of the leading causes of serious injury and death on BC construction sites, and most happen on ordinary jobs: a roof, an open stairwell, a ladder that is a little too short. This guide explains, in plain language, how fall protection works on a residential build in British Columbia: the rules, who is responsible, the equipment, the numbers that matter and how to plan a rescue.

Please read first: this is a free educational guide, not a certified training course. It does not replace hands-on fall protection training from a qualified provider, and it does not make anyone “competent” under the WorkSafeBC Regulation. Always follow the current WorkSafeBC Part 11 and your equipment manufacturer’s instructions.

Who it’s for: builders, site supervisors, trades, new workers and homeowners who want to understand what a safe site looks like.

In this guide: Why it matters · When you need it · Who is responsible · Choosing a method · Hazard assessment · The equipment · Forces and clearance · Control zones · Rescue · Inspection and fit · Real incidents and the human factor · Builder checklist · Self-test · Key words

1. Why fall protection matters

A fall happens faster than anyone can react. A person falls about 5 m (16 ft) in the first second, and a 1.8 m (6 ft) fall ends at roughly 21 km/h. Even short falls kill: when we trip, we instinctively throw our arms out and dive forward, so the head and neck often take the impact.

Fall protection is also a legal matter. After the 1992 Westray mine disaster in Nova Scotia, where 26 miners died, Canada amended the Criminal Code in 2004 (Bill C-45, often called the Westray Law). Section 217.1 says anyone who directs how another person does work must take reasonable steps to prevent bodily harm. Supervisors, project managers and company directors can now face criminal charges, and being an incorporated company does not shield them.

The protection is due diligence: being able to show, in writing, that you took every reasonable step. A useful test for every decision on site: would a sensible, careful person do this in the same situation?

The four types of falls

Type Examples on a house build
To a lower level Off a roof edge, through a floor or stair opening, off a deck, scaffold or ladder
On the same level Slips and trips on mud, ice, frost, cords and scrap lumber
Into or onto a hazard Onto rebar or machinery, into an excavation or water
On stairs Temporary or unfinished stairs without handrails

Other common fall hazards: skylights and fragile roofing you can break through, unguarded balconies, window openings, and roofs that are wet, frosty or covered in sawdust.

The numbers

  • In Canada, more than 40,000 workers are hurt in falls every year.
  • A WorkSafeBC summary of construction deaths in BC from 1996 to 2005 counted 49 deaths from falls (from elevations, roofs and scaffolds). Only asbestos-related disease killed more construction workers in that period.
  • Each death also costs the industry experienced people: co-workers who witness a fatality often leave construction for good.

2. When you need fall protection in BC

Situation What’s required
A worker could fall 3 m (10 ft) or more A fall protection system must be used
A fall of less than 3 m with a higher risk than landing on a flat surface (rebar, machinery, water, an open vat) A fall protection system must be used
Work at 7.5 m (25 ft) or more without permanent guardrails, or using a control zone or procedures A written fall protection plan must be on site before work starts
Before a worker enters an area with a fall risk The worker must be instructed in the system and procedures for that area

Our advice goes further than the minimum: if any form of fall protection is being used, write a plan, even if it is only a few lines. WorkSafeBC has a fillable plan template you can start from.

There is no “safe distance” from an unguarded edge written into the regulation. People can trip and stumble a long way. Staying back is only acceptable as part of a planned control zone (section 8).

What a fall protection plan must contain

The written plan must be at the workplace before work starts, and it must spell out:

  1. The fall hazards expected in each work area.
  2. The fall protection system to be used in each area.
  3. How the system is assembled, maintained, inspected, used and taken down.
  4. Where the anchors are, how they are inspected, and the rejection criteria (when an anchor must not be used).
  5. How to rescue a worker who has fallen and is hanging in a harness or safety net and can’t get out alone.

A good plan also lists the people on site, the equipment by type, the clearance calculation for each tie-off point, the communication method and who signs it off. A plan that only ticks boxes is worth little: every worker on the roof should be able to explain it.

Where the rules are written

BC’s workplace safety rules come in two parts: the Workers Compensation Act, which sets out the general duties of employers, supervisors, workers and prime contractors, and the Occupational Health and Safety Regulation, which has the detailed rules.

Regulation part What it covers
Part 4 General conditions, including guardrails, housekeeping and safe access
Part 8 Personal protective equipment, including hard hats, boots and eye protection
Part 11 Fall protection: when it’s required, plans, anchors, harnesses, lifelines, control zones
Part 13 Ladders, scaffolds and temporary work platforms
Part 32 Evacuation and rescue
Part 34 Rope access (specialized work on ropes)

Equipment standards

  • CSA (Canadian Standards Association) approved gear is accepted across Canada.
  • ANSI (American National Standards Institute) approved gear is also accepted in BC.
  • A company or site can set stricter rules than the law (for example, “CSA only” or tie-off from a lower height). Workers must follow the site’s rules while on that site.
  • No label, or a label you can’t read, means the gear can’t be used.

3. Who is responsible

The key question in any investigation is simple: did you give direction to this person? If yes, you carry employer-level responsibility for their safety, whatever your title and whether or not you pay them. A journeyman directing an apprentice counts.

Role Main duties
Employer Fix hazards; make workers aware of known and foreseeable hazards; provide and maintain equipment and make sure it is used; train and supervise; have a health and safety program; cooperate with WorkSafeBC
Prime contractor (often the general contractor) Coordinate safety for every trade on a multi-employer site; make sure unsafe conditions are corrected before work goes ahead
Supervisor Make sure workers know the hazards in their area, have been trained, follow the rules and use their protective equipment
Worker Use the fall protection provided; inspect gear before use; report hazards and damaged equipment
Whoever gives direction is responsiblePrime contractor (often the GC)Coordinates safety for every trade on sitegives directionEmployerPlans, gear, training; fixes hazardsgives directionSupervisorMakes sure workers know the hazards and follow rulesgives directionWorkerUses the gear, reports hazards, can refuse unsafe workThe one questionDid you give direction to this person?Yes = you’re responsible, paid or notCompetent workerQualified + trained + experiencedOnly the employer decidesDue diligenceWritten proof of every reasonable step:plans, checked cards, inspections, talksxeroxbuilders.ca

Worker rights

  • The right to know about hazards that could hurt them.
  • The right to participate in health and safety, including hazard assessments and rescue planning.
  • The right to refuse work they believe is unsafe.

A course card is not competency

A “competent” worker is adequately qualified, suitably trained and has sufficient experience. A training card covers the first two at most. Only the employer can decide a worker is competent, and should verify experience rather than take someone’s word for it.

4. Choosing a method: the hierarchy

Safety professionals rank controls from most to least effective. Always start at the top.

Start at the top: remove the hazard before reaching for PPEMOST EFFECTIVEElimination: remove the hazard (do the work on the ground)Substitution: swap for something safer (lift instead of ladder)Engineering: guardrails, hole covers, engineered anchorsAdministrative: plans, signs, procedures, trainingPPE: harness, lanyard, hard hatLEAST EFFECTIVEPPE is the least effective control. The rescue plan is the real last line of defence.xeroxbuilders.ca

For work at height, BC uses this order, choosing the highest one that is practicable:

  1. Guardrails
  2. Fall restraint: a line short enough that the worker cannot reach the edge
  3. Personal fall arrest: catches the worker after they fall
  4. Safety nets
  5. Control zones with a safety monitor
  6. Other written procedures acceptable to WorkSafeBC
Three ways to protect a worker at an edge1st choiceGuardrailA rail stops the fall happening2nd choiceFall restraintLine too short to reach the edge3rd choiceFall arrestCatches you after you fallxeroxbuilders.ca

Guardrails and restraint are preferred because nobody actually falls, so there is no impact and rescue is simple. From fall arrest down, a worker really does fall, and you need a proper rescue plan.

Guardrails

  • A guardrail has a top rail about 1 m (just over 3 ft) high, a mid rail halfway down and, where tools or material could fall on people below, a toe board.
  • It must be built to the strength and height rules in WorkSafeBC Part 4, and be secured so it can’t be knocked loose.
  • If a guardrail has to come off to land material or do work, the area becomes an unguarded edge: protect the workers another way, and put the guardrail back as soon as the work is done.
  • Cover floor holes with secured, marked covers strong enough to hold the expected load.

Safety nets

  • Nets catch a falling worker (and debris) below the work area. They are more common on large structures than on houses.
  • Nets must be installed and inspected by a qualified person, hung as close as practicable below the work, and kept clear of anything the worker could hit if the net stretches.
  • Check nets for torn mesh, damaged ropes, loose attachments and debris before each shift. A net that has caught a person must be inspected before it is used again.

Ladders

  • Pick the right ladder for the load: check the grade and weight rating on the label, and count your weight plus tools and material. A Grade 1AA ladder is rated for 375 lb.
  • A step ladder is a work ladder: face the work and the steps. Never stand on the top step or the top cap.
  • An extension ladder is mainly for getting up and down. Set it about 1 ft out for every 4 ft of height, extend it about 1 m (3 ft) above the landing and tie it off.
  • Keep three points of contact, and don’t carry heavy loads up the ladder.
  • If the ladder is too short, get a longer one or a lift. Don’t stretch, lean out or stand on the top.
  • Inspect before use: cracked or bent rails, loose rungs, missing feet or labels mean the ladder is out of service.

5. Hazard assessment

Measure a hazard the way you’d measure lumber: with a standard tool. For hazards, the tool is probability × severity.

  1. Recognize the hazard.
  2. Measure it: how likely, and how bad if it happens?
  3. Control it. Severity rarely changes (a 6 m fall is always serious), so controls mainly bring the probability down.
  4. Monitor and improve. Ask the workers doing the job; they often find the best fix.
Risk = likelihood × severity12342468369124812164 Major3 Serious2 Slight1 TrivialSeverity1 Most unlikely2 Unlikely3 Likely4 Most likelyLikelihood (probability)1–2 Maintain controls3–4 Review controls6–8 Improve controls9–16 Improve or STOPExample: lift job at 20 ft = 4 × 4 = 16, stop (solid box). After controls: 2 × 4 = 8 (dashed box).xeroxbuilders.ca

A written hazard assessment should cover: the hazards; inspections and tests needed and who does them; the protective equipment required; the equipment needed for a rescue; and how the crew will communicate in an emergency (radio, phone, satellite phone in remote areas). Date it and have it approved by a supervisor.

6. The equipment

A personal fall arrest system has five parts: anchorage, connecting components, full-body harness, an energy-absorbing lanyard or self-retracting lifeline, and a rescue plan. The gear catches you; the rescue plan gets you down alive.

The parts of a personal fall arrest system123456781AnchorStrong point; holds 5,000 lb (22 kN)2LifelineRope or cable from the anchor3Rope grabLocks onto the lifeline in a fall4Shock absorberTears open to soften the stop5LanyardConnects harness to the anchor6Full-body harnessBack D-ring between the shoulders7Unguarded edgeAn edge with no guardrail8ClearanceRoom below to stop safelyxeroxbuilders.ca

Personal protective equipment and boots

Personal protective equipment for work at height1234561Hard hat with chin strapStays on when you fall or dive forward2Safety glasses or face shieldFace shield for grinding3High-visibility vestSo machine operators can see you4Full-body harnessCSA or ANSI label; inspect every shift5GlovesGrip and hand protection6Safety bootsCSA patch; soft flat soles on roofs, lugs on mudxeroxbuilders.ca
  • Most falls start with a slip or trip, so boots are fall prevention. Look for the CSA patch, good ankle support and soles that aren’t worn smooth.
  • Roofing: soft, flat rubber soles grip shingles and don’t damage the roof. Deep lugs trap gravel that rolls like ball bearings.
  • Ground work: deep-lug soles for mud and uneven ground.
  • Never modify a tool or remove its guard. A saw blade on a grinder or a guard taken off a saw gives no warning before it injures.

Anchors

Anchor Fall restraint Fall arrest
Temporary 3.5 kN (800 lb), or 4 × the worker’s weight 22 kN (5,000 lb), or 2 × the maximum arresting force per worker, to manufacturer or engineer specifications
Permanent 22 kN (5,000 lb) 22 kN (5,000 lb)

Each worker needs their own anchor point. A rule of thumb when judging structure: would you be comfortable hanging your pickup truck from it? Never tie off to ceiling grid, plumbing pipe, cable tray or a single stud. The anchor is the device (a strap, clamp or bolted eye); the anchorage is the structure it is attached to.

Harness types

Type Use D-ring location
A Fall arrest (standard) Back, between the shoulder blades
D Controlled descent Front or sides (not at the waist)
E Confined space entry and evacuation On each shoulder strap, for lifting straight up
L Ladder climbing systems Front
P Work positioning Waist (hips). Not for fall arrest.
Harness types: the letter tells you where the D-rings areType AFall arrestBack, betweenshoulder bladesType DControlled descentFront or sides,not at waistType EConfined spaceEach shoulder,lift straight upType LLadder climbingFront, chestor sternumType PPositioning onlyBoth hips;not fall arrest= where the D-ring(s) sit. One harness can carry several letters; check the label.xeroxbuilders.ca

Harnesses must carry a CSA or ANSI label (both are accepted in BC). CSA-approved harnesses include a fall arrest indicator that shows permanently once the harness has stopped a fall. A body belt is never acceptable for fall arrest. Buy a comfortable, good-quality harness: a harness that hurts gets taken off.

Lanyards

  • Use the shortest lanyard that lets the work get done, with an energy absorber whenever possible.
  • Never knot a lanyard to shorten it, and never join two lanyards together.
  • Since 2017, CSA lanyards carry a standard white label. Read it for the maximum free fall, the weight range including tools and the maximum deployment (how far the shock pack stretches), which you need for clearance. Older lanyards without this label are still around.

Self-retracting lifelines (SRLs)

Class Mounting Over an edge? Rescue device?
SRL Above the back D-ring No No
SRL-R Above the back D-ring No Yes
SRL-LE (leading edge) Can be at foot level Yes No
SRL-LE-R Can be at foot level Yes Yes

An SRL locks quickly, so the fall is short. That makes it a good choice when working lower, where a 1.8 m lanyard plus its shock pack might not stop you before you hit the level below. Typical inspection and re-certification: light use, yearly inspection and every 5 years; moderate to heavy use, every 6 months and every 2 years; continuous use, every 3 to 6 months and every year (always follow the manufacturer).

Lifelines, rope grabs and connectors

  • A vertical lifeline takes one worker, must reach within 1.2 m (4 ft) of the ground, must be free of knots except a stopper knot at the bottom, and must be protected from sharp edges.
  • A rope grab has an arrow that must point up. Connect it with a locking carabiner or a lanyard no longer than 0.9 m (3 ft). Maximum free fall is 1.8 m (6 ft).
  • A horizontal lifeline must be engineered or manufactured, installed to written instructions kept on site, and inspected by a qualified person.
  • Snap hooks and carabiners must be self-closing and self-locking, rated 22 kN (5,000 lb) and compatible with what they clip to. Mismatched parts can “roll out” and open on their own.

Anchor slings

  • An anchor sling is a strap, wire rope or chain wrapped around a beam or structural member to create an anchor point where you can’t clip on directly.
  • It can be used for fall arrest, fall restraint, work positioning, suspension or rescue. Using one to anchor a horizontal lifeline needs a qualified person to design, install and supervise it.
  • Before use, check for broken stitching, excessive wear, stiffness and weather damage. Never load it beyond its rating, and keep it off sharp edges.

Horizontal lifelines

  • A horizontal lifeline is a cable or line between two or more anchors that lets a worker move sideways while tied off, when there is no anchor overhead.
  • The line between anchors must not slope more than 5° (CSA Z259.13).
  • A temporary system may only be used if it is manufactured for the purpose and installed to the maker’s written instructions, or installed to instructions certified by a professional engineer. Those instructions must be kept at the site.
  • A qualified person must inspect it as soon as it is installed and regularly while it is up. Anyone who sees a problem tags it and takes it out of service.
  • Horizontal lifelines sag a lot when they catch a fall, so they need extra clearance below.

Snap hooks and carabiners in more detail

  • They must be self-closing and self-locking, opening only with two separate deliberate actions, and be marked with their strength and maker.
  • A carabiner is a metal loop with a spring gate. It is cheap and useful, but it must still be rated for fall protection.
  • Never clip two snap hooks together, never clip more than one hook into a D-ring unless it’s designed for that, and retire any hook that has been in a fall.
  • Check for corrosion, weather wear, burrs, cracks, bending and a gate that doesn’t close and lock by itself.
Roll-out: how a wrong connection opens a hook1. Small ring sitsagainst the gate2. Hook twists; ringpresses the gate3. Gate opens andthe hook slips offPrevent it: self-locking, double-action hooks, and only connect to rings the hook is made for.xeroxbuilders.ca

7. Forces, free fall and clearance

The fall doesn’t hurt; the sudden stop does. The maximum arresting force is the short, sharp peak force on the body as the fall is stopped. It depends on the worker’s weight, how far they fall and how well the system absorbs energy.

Force What it means
4 kN (about 900 lb) Typical limit of a correctly used energy absorber
6 kN (about 1,350 lb) Legal limit without an energy absorber
8 kN (about 1,800 lb) Legal limit with an energy absorber used to the manufacturer’s instructions
22 kN (about 5,000 lb) Minimum strength of a fall arrest anchor

To keep the force down: anchor at or above shoulder height (higher is better), choose the highest anchor that still lets you work, use the shortest practical lanyard and use an energy absorber. If the only anchor is at your feet, add a riser or use a leading-edge SRL.

Required clearance below the anchorGround or level belowLLLanyard lengthEAEEAEEnergy absorber extensionDSDSD-ring slide / harness stretchHHHeight of worker below D-ringSMSMSafety marginRC = L + EAE + DS + H + SMThe ground must be farther below the anchor than RCxeroxbuilders.ca

Worked example: lanyard 1.8 m (6 ft), energy absorber extension 1.2 m (4 ft), D-ring slide 0.3 m (1 ft), worker 1.8 m (6 ft) below the D-ring, safety margin 0.9 m (3 ft). Required clearance = 1.8 + 1.2 + 0.3 + 1.8 + 0.9 = 6.0 m (20 ft) below the anchor. If the ground is closer than that, change the setup.

Second example (with a longer shock pack): lanyard 1.8 m (6 ft), energy absorber extension 1.8 m (6 ft), D-ring slide 0.3 m (1 ft), worker 1.8 m (6 ft), safety margin 0.9 m (3 ft). Required clearance = 6 + 6 + 1 + 6 + 3 = 22 ft (about 6.7 m). The lanyard label tells you the maximum deployment to use for the extension.

Free fall distance and total fall distance

Term What it means
Free fall distance How far you drop before the system starts to slow you down. The longer it is, the more force hits your body, the anchor and every part of the system. Keep it to 1.8 m (6 ft) or less.
Total fall distance The full distance from where the fall starts to where you stop, after every part of the system has stretched out (lanyard, shock pack, harness).
Required clearance Total fall distance plus your body below the D-ring and a safety margin. The ground or level below must be farther away than this.

Research shows the short forces of a fall arrest are unlikely to cause injury if they act upward through the buttocks and spine and stay under about 9 kN (2,000 lb). That is why harness fit and a shock absorber matter. The forces also strain the anchor and gear in ways you can’t see, which is why gear that has stopped a fall is retired.

Swing fall: keep the anchor directly above youWrong: anchor off to the sideAnchor far to the sideSwings into the columnRight: anchor directly aboveFalls straightdown, short stopxeroxbuilders.ca

A swing fall happens when the anchor is off to the side. The worker swings like a pendulum and can hit columns, walls or the ground. Keep the anchor directly overhead.

8. Control zones

Control zone and buffer zone on a flat roofControl zone: 2 m (6.5 ft)Buffer zone: another 2 m (6.5 ft)Safe work areaNo tie-off needed in hereMUnguarded roof edgeRaised warning line, 2 m inControl zone: tie off in hereBuffer zone (multi-trade sites)M = safety monitor, watches onlyNo tie-off: stay 4 m (13 ft) from the edgeFlat roofs only (low slope)Needs a written planCover every edge and cornerNot a free safe distancexeroxbuilders.ca
  • A control zone is a band at least 2 m (6.5 ft) wide along an unguarded edge, marked by a raised warning line. It is only for flat or very low-slope roofs.
  • Inside the control zone, workers must be protected (for example, tied off). A trained safety monitor watches the zone and does no other work.
  • Many BC sites with several trades add a further 2 m buffer inside the warning line, so unprotected workers stay about 4 m (13 ft) from the edge.
  • A control zone needs a written plan and must cover every edge, including corners. WorkSafeBC investigations have found falls where a corner was missed or the line was too close to the edge.

9. Rescue and suspension trauma

Ask this on every job at height: can we get a fallen worker down in under 5 minutes? If the answer isn’t a clear yes, fix it before work starts. Workers must be involved in making the emergency response plan, and it must be kept current.

Get a hanging worker down in under 5 minutesRescue goal: down in under 5 minWorker pumps legs, scrunches toesBlood pools in the legsLeg straps act like tourniquetsFall3 min: feels bad~5 min: likely unconscious10 min: death possiblexeroxbuilders.ca

Suspension trauma (orthostatic intolerance) happens when a person hangs upright and still. Leg muscles normally help pump blood back to the heart; hanging still, blood pools in the legs and the leg straps press like tourniquets. A worker can lose consciousness within minutes, and death can occur within about 10 minutes. While waiting, a worker should keep moving their legs, and use trauma relief straps if the harness has them. After a rescue, call 911 and follow the first aid attendant’s direction.

Rescue equipment can include rescue ladders, tripods and winches, and SRLs with a rescue device. Rescuers need protection at least as good as the fallen worker’s. Never work alone at height. Two people is the minimum: one to work, one to raise the alarm and start the rescue.

What the rescue plan should cover

  • Who does the rescue, and that they are trained and have practised it.
  • How the worker will be reached: from below with a ladder or lift, from above with a rescue device, or by lowering them.
  • Equipment: listed, inspected, documented and kept close to the work, not locked in a truck.
  • Communication: what works on this site (radio, cell phone, satellite phone in remote areas, hand signals or a whistle), and that it has been tested. Know the site address for 911.
  • First aid: who the first aid attendant is and what services are on site.
  • Emergency contacts: names and phone numbers posted where everyone can see them.

Rescue hazards

  • The rescuer can become a second victim. Rescuers need fall protection at least as good as the fallen worker’s.
  • Entanglement in ropes, lanyards and rigging.
  • Exhaustion: lifting or holding a person is very hard physical work.
  • Poor judgement under stress: rushing, skipping steps or improvising. This is why rescues must be planned and practised before they are needed.
  • Weather, darkness, sharp edges and overhead power lines.

Self-rescue devices

Some harnesses have trauma relief straps: foot loops stored in pouches that a hanging worker clips together and stands in. Standing takes pressure off the leg straps and keeps blood moving. Webbing step ladders hung from the lanyard work the same way. They buy time; they do not replace the rescue plan.

10. Inspection, putting on the harness, and storage

Before every use, check

  • Hardware: D-rings, buckles, hooks: cracks, bends, corrosion, sharp edges; gates close and lock
  • Webbing and rope: cuts, frays, burns, chemical or paint damage, mold, stiffness, knots
  • Stitching: pulled or broken threads; shock pack not torn open
  • Labels: present and readable; fall indicator not deployed
  • UV stripe: if the coloured thread in the webbing has faded, the gear is worn out

Any gear that has stopped a fall, or shows damage, comes out of service immediately. Destroy it or return it to the manufacturer so it can’t find its way back to the tool shed. Cutting the D-ring off a retired harness is a simple way to make sure it is never used again.

Reporting damage and falls

  • A worker who has a fall, or finds damaged gear, must report it right away to someone who can fix it: a supervisor, manager or site safety person.
  • The employer removes defective equipment from service, tags it, and returns it to the manufacturer or destroys it.
  • A fall arrest system that has stopped a fall stays out of service until every part has been inspected and re-certified, or replaced. The energy absorber may be partly torn open, and a self-retracting lifeline may need factory service.
  • Always follow the manufacturer’s inspection instructions. Typical self-retracting lifeline schedules range from a yearly inspection for light use to every 3 to 6 months for continuous use.

Things that damage gear

  • Sunlight (UV), heat, welding sparks and arc flash
  • Paint, solvents, acids and other chemicals
  • Sharp or rough edges and dragging on concrete
  • Moisture and mold from being stored wet
  • Being thrown in a truck bed or toolbox with sharp tools

Coated (impervious) harnesses can be wiped or hosed clean, which suits painters and plumbers, though they are stiffer to wear.

Keeping records

Keep written records of fall protection plans, hazard assessments, training, equipment inspections and safety talks. BC fall protection courses teach keeping them for at least 1 year, or 2 years if there was an incident or unplanned event. Our practice is simpler: keep everything at least 2 years. Good records are your due diligence if anything ever goes wrong.

Putting on a harness (donning)

  1. Inspect the harness.
  2. Hold it by the back D-ring and shake it so the straps fall into place. Undo the chest and leg straps.
  3. Slip it on like a vest, one arm at a time. The D-ring sits on your back between the shoulder blades.
  4. Bring each leg strap up between your legs and buckle it. You should fit two fingers under each strap.
  5. Buckle the chest strap 15 to 20 cm (6 to 8 in) below the shoulders. Tighten both shoulder straps evenly.
  6. Have a co-worker check the fit and D-ring position.

To take it off, unbuckle the leg and chest straps, slip it off the shoulders and hang it in a clean, dry place out of the sun.

11. Real incidents and the human factor

Westray mine, Nova Scotia, May 9, 1992

The Westray coal mine opened under heavy pressure to produce. In its few months of operation there were roof falls and faulty equipment, and a miner who reported safety problems to inspectors was fired. Methane gas built up, the mine exploded, and all 26 miners underground were killed; only 15 bodies were ever recovered. The public inquiry report was titled The Westray Story: A Predictable Path to Disaster. No manager was ever convicted, and the families’ long campaign led to Bill C-45 and Criminal Code section 217.1 in 2004. Westray Mine · Inquiry report (PDF)

Lesson: pressure to produce never justifies switching off safety, and the people in charge are now personally accountable.

Bosun’s chair and swing stage123451Bosun’s chair: a seat hung from one rope2Independent lifeline: its own rope and anchor3Swing stage: a hanging work platform4Suspension ropes raise and lower it5Each worker has their own lifelinexeroxbuilders.ca

Suspended work, like bosun’s chairs and swing stages, depends on every worker being tied to an independent lifeline before they get on. The Toronto case below shows what happens when that is skipped.

More incidents

  • Toronto, December 24, 2009. Six workers boarded a suspended swing stage to ride down at the end of the day, with only two harnesses between them. The platform broke apart and four men fell 13 storeys to their deaths. The project manager was convicted of criminal negligence and sentenced to 3.5 years in prison. CBC
  • Kelowna, July 12, 2021. A tower crane collapsed while being dismantled, killing five people. A forensic report found a section was lifted before it was fully detached. Global News
  • BC balcony fall. A worker fell about 15 m climbing from a balcony onto a work platform. He wore a harness but wasn’t tied off, and the prime contractor was faulted for not correcting the unguarded balcony. WorkSafeBC
  • BC roof fall. A roofer died when an anchor that hadn’t been installed to the manufacturer’s instructions failed. WorkSafeBC

Each of these cases has a lesson: the deadline and bonus in Toronto, skipping specialists in Kelowna, an unguarded balcony left in place, and an anchor installed the wrong way. Most serious falls trace back to a decision someone made, not to bad luck. That is why safety people say there are no accidents, only incidents.

Near misses: Bird’s pyramid

For every serious injury, about 600 near misses1serious or disabling injury10 minor injuries30 property-damage incidents600 near misses (no injury, no damage)Fix the near misses at the bottom to prevent the injury at the top (Frank Bird, 1969).xeroxbuilders.ca

Safety researcher Frank Bird studied a very large number of workplace incidents and found that serious injuries sit on top of many smaller events. The near misses at the bottom are free warnings. Report them, talk about them at the morning safety meeting, and fix the cause.

Experience is not the same as safety

Experience can breed complacencyRiskMost cuts and bumps: year 1Complacency peak, years 8 to 10Settles once people have seen what can go wrongYear 1Years 8 to 10Later careerSerious incidentsMinor injuries (illustration, not real data)xeroxbuilders.ca

New workers have the most small injuries, but they are watched closely. Safety trainers often point out that the bigger danger is the experienced worker who has done the job so many times without a problem that they stop thinking about it. Watch your experienced people as closely as your new ones.

The four everyday causes

Cause What it looks like on site
Complacency “I’ve done this a hundred times.” Skipping the tie-off for a quick job.
Impatience Rushing to finish; using a ladder that is too short instead of fetching the right one.
Anger Working upset or frustrated, and making poor decisions.
Fatigue Long shifts and overtime; slower reactions and careless mistakes.

Often two or three of these act together. A typical example: one fixture left to install, the right ladder is two floors down, so the worker stands on the top step of a short one, and it kicks out. Another: the only harness left is damaged, but the worker wants the overtime and wears it anyway. In both cases the worker is the one who gets hurt. If it can hurt you, it is your business.

Don’t forget the drive

For most workers, the most dangerous part of the day is the drive to and from the site. Rushing back for a forgotten tool or badge, or driving tired after a long shift, causes serious crashes. Treat travel as part of the job: plan ahead, don’t rush and don’t drive exhausted.

12. Builder checklist

  • Guardrails first at floor edges, stair openings and roof edges where practicable
  • Written hazard assessment and fall protection plan for any work using fall protection
  • Rescue plan that gets a worker down in under 5 minutes, with rescue gear on site
  • Every anchor identified, rated and installed to manufacturer or engineer instructions
  • Clearance calculated for each tie-off location
  • CSA or ANSI labelled gear, inspected before every shift, with trauma relief straps
  • Workers’ training cards checked and copied; experience verified; competency decided by the employer
  • Each worker instructed in the site’s system before entering a fall-risk area
  • No one works alone at height
  • Right ladders on site, inspected, tied off, and nobody on the top step
  • Proper boots and PPE for each task; no modified tools or removed guards
  • Near misses reported and discussed at safety meetings
  • Damaged gear tagged, removed and destroyed; gear stored clean and dry
  • Records kept: plans, training, inspections, safety talks (keep at least 2 years)

13. Quick self-test

At what height is fall protection required in BC?

3 m (10 ft), or less if the fall carries extra risk, such as landing on rebar or into water.

When must a written fall protection plan be on site?

When workers could fall 7.5 m (25 ft) or more without permanent guardrails, or when a control zone or procedures are used. We recommend a plan whenever fall protection is used.

What is the first choice of fall protection?

Guardrails, followed by fall restraint, fall arrest, safety nets, control zones and procedures.

How strong must a fall arrest anchor be?

22 kN (5,000 lb), or twice the maximum arresting force per worker where designed by the manufacturer or an engineer.

What is the required clearance formula?

RC = Lanyard + Energy absorber extension + D-ring slide + Height of worker + Safety margin.

Which SRL can be used at foot level over an edge?

A leading-edge SRL: SRL-LE or SRL-LE-R.

How fast must a fallen worker be rescued?

Aim for under 5 minutes. Suspension trauma can cause unconsciousness within minutes and death within about 10.

Can you keep using a harness after it stopped a fall if it looks fine?

No. Remove it from service immediately.

Is a harness without a CSA or ANSI label acceptable?

No. Harnesses must meet the CSA or ANSI standard, and the label must be readable.

Name three rescue hazards.

Entanglement, exhaustion and poor judgement under stress. The rescuer can also become a second victim.

How long should fall protection records be kept?

At least 1 year, or 2 years if there was an incident or unplanned event.

What is the required clearance for a 6 ft lanyard, 6 ft shock pack extension, 1 ft D-ring slide, 6 ft worker and 3 ft safety margin?

22 ft (about 6.7 m) below the anchor.

14. Key words

Word Meaning
Anchor / anchorage The device you tie to / the structure the device is attached to
Bosun’s chair A seat hung on a rope for work on the side of a building
Clearance The room needed below you to stop safely after a fall
Competent worker Adequately qualified, suitably trained and with sufficient experience; decided by the employer
Control zone A marked band at least 2 m wide along an unguarded edge, used only with a written plan
CSA / ANSI Canadian and American standards bodies that test and approve equipment
Donning / doffing Putting on / taking off a harness or other gear
Due diligence Proof that you took every reasonable step to keep people safe
ECP Exposure or emergency control plan
Energy absorber (shock pack) Part of a lanyard that tears open to soften the stop
Fall arrest A system that catches you after you fall
Fall restraint A system that stops you reaching the edge, so you can’t fall
Fall protection plan The written plan for a site’s fall hazards, systems, anchors and rescue
Free fall distance How far you drop before the system starts to slow you
Full-body harness Straps around the legs, chest and shoulders that spread the fall forces
Guardrail A rail system at an edge that stops a fall happening
Lanyard A short line of webbing, rope or wire between the harness and the anchor
Lifeline A rope or cable fixed to an anchor that a worker connects to
Maximum arresting force The short peak force on the body when a fall is stopped
PPE Personal protective equipment: hard hat, boots, glasses, gloves, harness
Prime contractor The party that coordinates safety for all trades on a site, often the general contractor
Rope grab A device that slides on a lifeline and locks if you fall
Safety monitor A trained person whose only job is to watch workers in a control zone
SRL Self-retracting lifeline (“yo-yo”) that reels in and out and locks in a fall
Suspension trauma Blood pooling in the legs while hanging still in a harness; can cause fainting and death
Swing fall Swinging like a pendulum because the anchor wasn’t directly overhead
Swing stage A hanging work platform raised and lowered on ropes
Total fall distance The full distance from the start of the fall to the stop
Unguarded edge An edge with no guardrail

Sources and further reading

WorkSafeBC OHS Regulation, Part 11: Fall Protection · WorkSafeBC fall protection plan template · Criminal Code, section 217.1 · Westray Mine

Written by Mandeep Singh, licensed residential builder and director of Xerox Builders, who completed BC fall protection training in November 2026. Illustrations by Xerox Builders.

Please note: This page is general safety information, not legal or professional advice, and it is not a substitute for certified fall protection training. Requirements were accurate to the best of our knowledge when published and can change. Always check the current WorkSafeBC Regulation and your equipment manufacturer’s instructions, and get training from a qualified provider before working at height.

Planning a home build in Vancouver, Burnaby or Surrey? We run safe, well-organized sites from day one.

Get a free quote