Types, Sizing, Cooling Rules, Outdoor Unit Placement and Local Requirements for Vancouver and Burnaby Homeowners
If you’re planning a new house, duplex, multiplex or laneway home in Vancouver or Burnaby, the heating system is one of the first decisions your design team will ask about. For most new homes in both cities today, the answer is a heat pump. Local emissions rules, the BC Building Code’s new cooling requirement and the mild coastal climate all point the same way.
This guide explains how heat pumps work, the main types, what each city requires, and what to settle before you apply for a permit.
How a heat pump works
A heat pump moves heat instead of making it. In winter it pulls heat from the outdoor air (or the ground) and moves it indoors; in summer it runs in reverse and cools the home, the same way an air conditioner does.
Natural Resources Canada says an air-source heat pump can be up to about 2 times as efficient as electric baseboard heating, and a cold-climate model up to about 2.5 times (approximate seasonal figures that vary with the home and the equipment). Metro Vancouver’s mild winters are well suited to air-source units, and cold-climate models are designed to keep working well below freezing.
The main types used in new homes
| Type | How it delivers heat | Often suits |
|---|---|---|
| Ducted air-source (central) | Outdoor unit connected to an indoor air handler; warm or cool air goes through ducts to every room | Larger houses and duplex units where ducts can be planned into the framing from the start |
| Ductless mini-split / multi-split | Outdoor unit feeds one or more wall, ceiling or floor heads; no ducts | Laneway homes, suites and compact units; zones with different schedules |
| Air-to-water (hydronic) | Heats water for in-floor radiant heating or radiators; some systems also make hot water | Owners who want radiant floors; needs a separate plan for cooling |
| Ground-source (geothermal) | Draws heat from the ground through buried loops or wells | Larger lots with room for drilling; higher upfront cost and extra City review |
| Heat pump water heater | Uses the same principle to heat domestic hot water | Any all-electric home; needs space and air volume around the tank |
What Burnaby requires
Burnaby follows the BC Building Code and has moved ahead of the provincial schedule on emissions. From January 1, 2024, new single- and two-family homes had to meet Emission Level 3 of the Zero Carbon Step Code, and the City announced that EL-4, Zero Carbon Performance, would apply from 2025. Builders can show compliance either with an energy model or with a signed declaration that systems such as space heating, water heating and cooking will be electric.
For most new Burnaby homes, that means an all-electric design: a heat pump for heating and cooling, electric or heat pump hot water and an electric or induction range. If you want any gas appliance, ask the Building Division first.
What Vancouver requires
Vancouver has its own building by-law (the VBBL). Since January 1, 2022, new low-rise homes have had to use zero-emission equipment for space heating and hot water. Under the 2025 VBBL, the prescriptive path for 1 to 3 storey homes still requires electric space heating and hot water (small gas fireplaces aside), along with heat pump controls, a programmable setback thermostat and a heat recovery ventilator. The performance path allows gas equipment if the energy model meets the City’s greenhouse gas limits.
On May 27, 2026, Council voted to direct staff to align the VBBL with the provincial code, which would make gas heating an option again. A motion is not a by-law, and at the time of writing we could not confirm that the amendments are in force. Ask the City which rules apply on the date you submit your permit application. Even if gas becomes an option, a heat pump remains a simple way to meet the cooling requirement below.
The new cooling requirement
For building permit applications made on or after March 8, 2024, the BC Building Code requires at least one designated living space in each new dwelling unit to be able to keep indoor air at 26°C or below. This can be done with passive measures such as shading and ventilation, with mechanical cooling, or with both. For houses, the cooling load has to be calculated using the CSA F280 standard. Plug-in window air conditioners don’t count; the equipment must be part of the building’s system.
In a duplex or a house with a suite, the rule applies to each dwelling unit, so plan cooling for every home on the lot. Vancouver applicants should confirm how the VBBL handles the same requirement.
Sizing: why the heat loss calculation matters
An oversized heat pump cycles on and off, costs more and can control humidity poorly; an undersized one leans on backup heat. Burnaby’s heat pump guide for existing homes asks for a design package that includes CSA F280 heat loss calculations, equipment selection, a balance point calculation and a duct layout where ducts are used, prepared by a TECA-certified designer or professional engineer. New homes also carry an energy model under the Step Code or the VBBL, so the mechanical designer and energy advisor should work from the same numbers.
Placing the outdoor unit
The outdoor unit is easy to forget until the site plan is nearly finished. Local guidance for heat pumps on existing homes gives a good idea of what each city looks for:
- Vancouver: the City’s bulletin for ground-oriented homes asks for ground-mounted, inverter-driven units at least 90 cm from the property line, out of required pathways and parking, with only one exterior unit per yard. It recommends a sound power level of 55 dBA or less, and every unit must meet the Noise Control By-law.
- Burnaby: the City’s guide keeps ground-mounted units out of required front and side yards and access paths. Under Burnaby’s noise bylaw, continuous noise is limited to 55 dBA during the day and 45 dBA at night (10 pm to 7 am), and the City suggests placing units away from neighbours’ windows, preferably at the rear, behind barriers.
- Wall, roof or deck mounts usually need extra review, and in Burnaby a building permit with engineered structural drawings.
On a new build, show each outdoor unit and its condensate drainage on the permit drawings so it isn’t squeezed into a side yard later.
Electrical service and rebates
- Electrical capacity: an all-electric home with a heat pump, heat pump water heater, induction range and EV charger uses much more power than a gas-heated one. Vancouver’s bulletin requires electrical load calculations, and duplexes and multiplexes with several systems may need a larger BC Hydro service.
- Rebates: BC Hydro’s main heat pump rebate is for replacing an existing heating system, and doesn’t list new construction as eligible. Programs for new homes change often, so check BC Hydro and CleanBC Better Homes before you finalize the design.
Decisions to settle during design
- Choose the system type (ducted, ductless, hydronic or a mix) before framing drawings are finished, so ducts and chases are planned in.
- Get the heat loss and cooling load calculations done and shared with your energy advisor.
- Locate outdoor units on the site plan, with noise and setbacks in mind.
- Confirm electrical service size with your electrician and BC Hydro.
- Confirm current local rules, especially in Vancouver.
Mechanical design happens during the design and permit stage, before construction. Once construction starts on a straightforward lot (relatively flat, with no significant trees and little slope), building a custom home typically takes about 10 months from foundation to finish (approximate).
Related reading
- BC Energy Step Code explained for Vancouver and Burnaby homeowners
- Passive House in Vancouver: what it is and what it takes
- Secondary suites in Vancouver and Burnaby: what makes a suite legal
- The building permit process in Vancouver and Burnaby, step by step
- Building Science: Net Zero & high-performance homes
Wondering which heating and cooling setup makes sense for the home you’re planning?
Sources
- City of Burnaby: Stronger climate requirements for new construction (January 2024)
- City of Burnaby: Air source heat pump retrofit info guide (PDF)
- City of Vancouver: Guide to the 2025 VBBL energy and GHG compliance paths for 1-3 storey residential buildings (PDF)
- City of Vancouver: Heat pumps for existing ground-oriented dwellings bulletin (PDF)
- Vanplex: Vancouver’s gas vote, explained (May 2026)
- Government of BC: Bulletin B24-08, protection from overheating (PDF)
- Government of Canada: Heat pump basics
- BC Hydro: Heat pump rebates for renovating your heating system
Rules and figures are approximate and change over time. Confirm the heating, cooling and emissions requirements for your property with your municipality and a qualified mechanical designer or energy advisor.





