Completed custom home project on Moscrop Street, Burnaby BC
Construction Insights

What Burnaby’s R1 Small-Scale Multi-Unit Housing zoning allows, what changed in late 2025, and how to tell if a multiplex works on your lot

Since July 2024, most single- and two-family lots in Burnaby can hold three to six homes. For owners and investors, that raises a simple question: is building a multiplex on a Burnaby lot actually a good investment? The answer depends on your lot, the rules that apply today and a few numbers you can check before spending money on design.

In short: Burnaby replaced its 12 old residential zones with one R1 Small-Scale Multi-Unit Housing district. Small lots can have 3 homes, larger lots 4, and lots of at least 281 m² near frequent transit up to 6. In late 2025 the City reduced the allowed height and lot coverage, so older feasibility studies may no longer be accurate.

What Burnaby’s R1 zoning allows

The City consolidated its 12 existing residential districts into one R1 Small-Scale Multi-Unit Housing district, effective July 1, 2024, to meet the Province’s housing legislation. The number of homes depends on lot size and on whether the lot is in a Frequent Transit Network Area (FTNA):

Lot up to 280 m²(3,014 sq ft)3 homesLot over 280 m²(3,014 sq ft)4 homesLot 281 m²+ nearfrequent transit6 homes
How many homes Burnaby’s R1 zoning allows, by lot size and transit location. Secondary suites count toward the total.
  • Up to 280 m² (3,014 sq ft): 3 homes
  • Over 280 m²: 4 homes
  • At least 281 m² inside an FTNA: 6 homes

Those homes can take several forms: a house with a suite and a laneway home, a cottage court of small detached homes, a multiplex of 3 to 6 units in one building, rowhouses, or duplexes. A secondary suite counts toward the total, must stay on the same title as its main home and can’t be stratified.

What changed in late 2025

In October 2025 Council approved changes to reduce the height and size of these projects. The City’s December 2025 summary shows front buildings limited to 10 m and 3 storeys for 3 to 6 units, rear buildings to 7.5 m and 2 storeys, and maximum lot coverage reduced by 5% to 10%. Parking outside transit areas went up to 1 space for the first unit and 0.5 per additional unit; inside an FTNA no parking is required.

The practical effect: on many lots you can still build the same number of homes, but each one may be a little smaller. Any pro forma done before these changes should be re-run.

The numbers that decide the investment

LandConstructionFeesLoanIllustration only: the real split depends on your lot, design and timing
Where the money goes in a typical multiplex project: land, construction, fees and soft costs, and financing. Illustration only, not a quote.
  1. Land value. In Burnaby, land is usually the biggest single cost. A multiplex works best when the land cost per buildable home is reasonable.
  2. Buildable floor area. Burnaby’s R1 zone doesn’t use a fixed floor space ratio. Size is controlled by height, setbacks and lot coverage, so a designer needs to sketch your actual lot.
  3. Servicing. Burnaby requires certain works and services for R1 projects, such as upgraded water, sewer or frontage improvements. These can add meaningful cost.
  4. Exit plan: sell or rent. Multiplex units can be stratified and sold, or kept as rentals. The answer changes your financing, timeline and return.
  5. Time. Design, permit and construction take time, and financing costs keep running. A realistic schedule matters as much as the budget.
Completed Moscrop Street home in Burnaby built by Xerox Builders
A completed Xerox Builders home on Moscrop Street, Burnaby.

When a multiplex usually makes sense

  • The lot is in or near a transit area, so you can build more homes with less parking.
  • The lot is flat or gently sloped, with no large protected trees in the building area.
  • You plan to hold some units long term, or sell into strong demand for family-sized homes.
  • Servicing upgrades are modest after the City reviews your lot.

How to check your own lot

  1. Find your lot area and confirm it’s zoned R1 on the City’s mapping.
  2. Check whether it’s inside a Frequent Transit Network Area.
  3. Ask a builder or designer for a quick massing sketch under the current (post-2025) rules.
  4. Get a rough construction and servicing budget before paying for full drawings.

We do this feasibility review for owners across Burnaby. It’s the cheapest way to find out whether your lot is a good multiplex candidate before committing to design.

Related reading

Please note: This page is general information, not legal, financial or professional advice. The facts, figures, bylaws, fees and code requirements described here were accurate to the best of our knowledge when it was published or last updated. These rules change often and differ from city to city, so some details may have changed since. Before you make decisions, please confirm the current requirements with your city’s planning and building department and with qualified professionals. We’re always happy to help you check what applies to your property.

Thinking about a multiplex on your Burnaby lot? We’ll check what you can build.

Call 604-786-7000Book a Free Site Visit

Mandeep Singh, Builder and Director at Xerox Builders
Written by
Mandeep Singh
Builder & Director, Xerox Builders Ltd. · BC Housing Licensed Residential Builder

Mandeep has been a licensed residential builder in BC for almost 10 years. He builds custom homes, laneway homes, duplexes and multiplexes in Vancouver, Burnaby, Surrey and Delta, and writes these guides so homeowners know what to expect before they build.

Share This Story, Choose Your Platform!

Recent Works

Tags